Unicable II LNB DUR-Line® UK124 - 24 satellite receivers simultaneously.

Unicable II LNB DUR-Line® UK124 can deliver signal to up to 24 satellite receivers simultaneously !. No need for expensive multiswitches, satellite dish signal is provided on one cable. Perfect for distributing SAT signals in multi-family homes, ground floor properties and for you, with multiple tuners. Your Receiver must support Unicable or Unicable II (JESS).With the Unicable II solution, you can easily establish an advanced setup with many dish receivers.

Compared to previous solutions with expensive multiswitches, multituner satellite dishes can now be made at a fraction of the cost. The benefits of Unicable 2 are:

• Lower your setup costs - no multiswitches, no cascades.
• Cheaper LNB
• Single line signal - the signal for all satellite receivers is drawn in the same downlead
• Connect up to 24 devices, all will have all transponders available independently of others.
• Backwards compatible

DUR-Line® UK124 is a Unicable II LNB. Only one cable is connected to the LNB. The signal is distributed to the digital satellite receiver, TV sets with DVB-S / S2 tuner and e.g. twin tuners on the same downlead (watch one program and record another).

Only condition for use is that your receiver can handle Unicable or Unicable II.The DUR-Line® UK124 Unicable II LNB switches via the EN50607 protocol. This protocol is also called Unicable II or JESS and allows up to 24 devices on the same LNB. The older protocol EN50494, called Unicable, is also supported, but limited to 8 devices. Therefore, before purchasing this Unicable LNB, it is important to know any limitations on receiving equipment. Unicable and Unicable II divide the signal into blocks. Unicable can address the first 8 blocks, while Unicable II can address all 24 blocks:

CH1: 1210MHz (EN50494+EN50607)
CH2: 1420MHz (EN50494+EN50607)
CH3: 1680MHz (EN50494+EN50607)
CH4: 2040MHz (EN50494+EN50607)
CH5: 1005MHz (EN50494+EN50607)
CH6: 1050MHz (EN50494+EN50607)
CH7: 1095MHz (EN50494+EN50607)
CH8: 1140MHz (EN50494+EN50607)

CH9: 1260MHz (EN50607)
CH10: 1305MHz (EN50607)
CH11: 1350MHz (EN50607)
CH12: 1475MHz (EN50607)
CH13: 1520MHz (EN50607)
CH14: 1565MHz (EN50607)
CH15: 1610MHz (EN50607)
CH16: 1725MHz (EN50607)
CH17: 1770MHz (EN50607)
CH18: 1815MHz (EN50607)
CH19: 1860MHz (EN50607)
CH20: 1905MHz (EN50607)
CH21: 1950MHz (EN50607)
CH22: 1995MHz (EN50607)
CH23: 2085MHz (EN50607)
CH24: 2130MHz (EN50607)

DUR-Line® UK124 Unicable II LNB Specification:

Input Frequency: Low Band: 10.70 - 11.70 GHz. High Band: 11.70 - 12.75 GHzL.O.Frequency Wide Band: 10.4 GHz L.O. Stability ± 1.0 MHz (max) @ 25 ° C ± 2.2 MHz (max) @ -40 ° C ~ + 60 ° CAmplification: 65 dB (max.)Cross POL. Isolation: 20 dB (min)Image Rejection: 40 dB (min)L.O. Frequency Phase Noise: -60 dBc / Hz @ 1 KHz (max.), -75 dBc / Hz @ 10 KHz (max.), -95 dBc / Hz @ 100 KHz (max.)Operating voltage: 11.5 - 19 VCurrent consumption (DC): 300 mA (max.)Operating temperature: -30 ° C ~ + 60 ° C

With Unicable II you gain complete freedom. All transponders that are in a SAT position will be available to all receivers, regardless of transponder or polarity, and independently of others. The DUR-Line® UK124 Unicable LNB is predefined in several Enigna2 boxes LNB listings, making it easier to setup correct values.

With Unicable II you gain complete freedom and nail down the costs. All transponders that are in a SAT position will be available to all receivers, regardless of transponder or polarity, and independently of others.